Synthesis and characterization of nanoparticulate MnS within the pores of mesoporous silica

Mesoporous silica was loaded with nanoparticulate MnS via a simple post-synthesis treatment. The mesoporous material that still contained surfactant was passivated to prevent MnS formation at the surface. The surfactant was extracted and a novel manganese ethylxanthate was used to impregnate the pore network. This precursor thermally decomposes to yield MnS particles that are smaller or equal to the pore size. The particles exhibit all three common polymorphs. The passivation treatment is most effective at lower loadings because at the highest loadings (SiO₂:MnS molar ratio of 6:1) large particles (>50 nm) form at the exterior of the mesoporous particles. The integrity of the mesoporous network is maintained through the preparation and high order is maintained. The MnS particles exhibit unexpected ferromagnetism at low temperatures. Strong luminescence of these samples is observed and this suggests that they may have a range of important application areas.     

High-performance liquid chromatography of sulfonamides and quinolones on p-tert-butyl-calix[6]arene-bonded silica gel stationary phase

The high-performance liquid chromatographic behavior of some sulfonamides and quinolones was studied on a p-tert-butyl-calix[6]arene-bonded silica gel stationary phase. The effect of mobile phase variables such as methanol content, ionic strength and pH on their chromatographic behavior was investigated. The retention behavior of sulfonamides on the stationary phase was compared with that on both Zorbax C₁₈-bonded silica gel and γ-(ethylenediamino)propyltriethoxylsilane-bonded silica gel (diamino-bonded phase). The retention mechanism of sulfonamides and quinolones on the stationary phase was also discussed. The results indicate that the stationary phase behaves as a reversed-phase packing and its separation selectivity is much better than that of not only Zorbax C₁₈ phase but also diamino-bonded phase. Some sulfonamides and quinolones were separated on the stationary phase, but the separation of sulfonamides is far more successful.     

One-phase supported titanium-based catalysts for polymerization of ethylene. III. ESR spectra of the ternary system Sio2—R3Al—TiCl4

The ternary catalyst systems based on activated silica, aluminum alkyl, and titanium tetrachloride were polymerized in an ethylene gas-phase polymerization process, and further studied using ESR spectroscopy. Two types of titanium (III) ESR-active centers were observed and a linear dependence between the concentration of that characterized by a rhombic anisotropic signal with g₁ = 1.962, g₂ = 1.945, and g₃ = 1.913 values and catalyst productivity was found. © 1993 John Wiley & Sons, Inc.     

Fused silica capillary tube isotachophoresis using a multichannel photodiode array detector

Isotachophoresis carried out in a 0.25 mm i.d. fused-silica capillary tube yielded high resolution, compared with that in a fluorinated ethylene-propylene polymer tube. The use of an ultraviolet-visible multichannel spectrophotometer with photodiode array as detector together with a cross flow cell (volume 0.01 μl) was investigated. The system was successfully applied to the analysis of cationic dyes such as neutral red, bismarck brown, and basic fuchsine.     

SYNTHESIS OF MESOPOROUS POLY(STYRENE-co-MALEIC ANHYDRIDE)/SILICA HYBRID MATERIALS VIA A NONSURFACTANT-TEMPLATED SOL-GEL PROCESS*

Mesoporous poly (styrene-co-maleic anhydride)/silica hybrid materials have been prepared. The synthesis wasachieved by the HCl-catalyzed sol-gel reactions of tetraethyl orthosilicate (TEOS) and styrene-maleic anhydride copolymerin the presence of 3-aminopropyl triethoxysilane (APTES) as a coupling agent and citric acid as a nonsurfactant template orpore-forming agent, followed by ethanol extraction. Characterization results from nitrogen sorption isotherms and powder X-ray diffraction indicate that polymer-modified mesoporous materials with large specific surface areas (e.g. 900 m~2/g) andpore volumes (e.g. 0.6 cm~3/g) could be prepared. As the citric acid concentration is increased, the specific surface areas, porevolumes and pore diameters of the hybrid materials increase.     

不同添加物和制备方式对Al2O3热稳定性的影响

通过水溶液成胶和丙三醇络事助成胶制备了不同的结构的γ－Ａｌ２Ｏ３,研究了Ｌａ,Ｓｉ,Ｂａ以及Ｌａ,Ｓｉ和Ｌａ,Ｂａ双组分改性对它们结构热稳定的作用,讨论了改性元素的引入方式及硅铝比的影响。结果表明,丙三醇络合助成胶能明显提高Ａｌ２Ｏ３的比表面积和孔径,并能显著改善Ａｌ２Ｏ３的热稳定性。     

The Effect of the Nature and Structure of Adsorbents on Interaction with Ibuprofen

The interaction of ibuprofen [2-(4-isobutylphenyl)propionic acid] with the surface of carbon and oxide adsorbents was investigated. The significant role of wide pores during the adsorption of ibuprofen on carbon adsorbents in the presence of protein molecules was demonstrated. At low concentrations ibuprofen is adsorbed on the surface of hydrophilic and hydrophobic adsorbents in the form of a monomer, but the contribution from the adsorbed dimer increases with increase in its concentration.     

Characterization of Titania/Silica Gel by Means of Low-Pressure Nitrogen Adsorption

Adsorbents synthesized by grafting of titania onto mesoporous silica gel surfaces at different temperatures were studied by means of nitrogen adsorption–desorption and water desorption. The pore size distribution f(R_p) of titania/silica gel depends on the titania concentration (C_TiO2) and the temperature of titania synthesis. Nonuniformity of TiO₂ phase is maximal at a low C_TiO2 value (3.2 wt.% anatase deposited at 473 K), and two peaks of the fractal dimension distribution f(D) are observed at such a concentration of titania, but at larger C_TiO2 values, only one f(D) peak is seen. More ordered filling of pores and adsorption sites by nitrogen, reflecting in the shape of adsorption energy distributions f(E) at different pressures of adsorbate, is observed for adsorbent with titania (rutile+anatase) grafted on silica gel at a higher temperature (673 K).     

新型介孔分子筛KIT-1加氢脱硫催化剂的研究

制备了新型的结构排列无序的介孔分子筛KIT-1和负载Ni, Mo的KIT-1加氢脱硫催化剂。实验结果表明MoO3较易分散在KIT-1的表面,而NiO则容易在其表面形成小晶粒。与以MCM-41和NaY分子筛为载体的Ni, Mo催化剂相比, KIT-1负载催化剂具有较高的加氢脱硫催化活性,因为KIT-1载体具有相互交错的三维孔道结构, 有利于反应物和产物的扩散, 而不容易受孔道堵塞的影响。